Hi guys and gals!
As you probably are aware by now, Alex has talked about us doing a discount for jzx.co.nz members.
We are happy to do a 10% discount off my already reasonable prices for members of this website!
Initially all this will require is pm me on here and let me know what work you want done,
or phone me at work and let me know you are on this forum and own a X chassis and want work done.
Eventually we will setup a system so that only validated members can get the discount ( buy a jzx.co.nz sticker or something )
Our work is of the highest quality and he takes great pride in his work, and our prices are very sharp!
Check out our website http://www.sincocustoms.co.nz
Any Questions, etc you can post on this thread or Pm me.
Sinco Customs - Custom fabrication offer!
-
- Member
- Posts: 5
- Joined: Mon Jan 17, 2011 8:52 pm
Sinco Customs - Custom fabrication offer!
Last edited by Sinco Customs on Tue Jan 25, 2011 5:30 pm, edited 2 times in total.
Re: Sinco Customs - Custom fabrication offer!
heres some pics of my sinco steampipe manifold for VVTI 1JZ-GTE , ceramic coated. t4 flange for T04z
and custom intake
and custom intake
Re: Sinco Customs - Custom fabrication offer!
do you guyz do engine mounts and shafts for a 1uz conversion? if so how much?
"Understeer is when you hit the wall with the front of the car.
Oversteer is when you hit the wall with the rear of the car.
Horsepower is how fast you hit the wall,
Torque is how far you take the wall with you."
Oversteer is when you hit the wall with the rear of the car.
Horsepower is how fast you hit the wall,
Torque is how far you take the wall with you."
-
- Member
- Posts: 5
- Joined: Mon Jan 17, 2011 8:52 pm
Re: Sinco Customs - Custom fabrication offer!
PowderJZX wrote:do you guyz do engine mounts and shafts for a 1uz conversion? if so how much?
We dont have anything made up but could do something if we had the car etc.
Mike
Re: Sinco Customs - Custom fabrication offer!
Hi, whats the cost for a non vvti single manifold with a t3 flange and a 38mm 'gate pipe? cheers
-
- Member
- Posts: 5
- Joined: Mon Jan 17, 2011 8:52 pm
Re: Sinco Customs - Custom fabrication offer!
moonboots wrote:Hi, whats the cost for a non vvti single manifold with a t3 flange and a 38mm 'gate pipe? cheers
The price would be $980+gst,but you will receive 10% discount.
Re: Sinco Customs - Custom fabrication offer!
Hey man,
Need one for an S15 SR20DET with the T28 Flange.
Have them in stock at all? Might give you a call this week sometime..
Need one for an S15 SR20DET with the T28 Flange.
Have them in stock at all? Might give you a call this week sometime..
Re: Sinco Customs - Custom fabrication offer!
so basically we are looking at 900 for custom made steam tube manifold and 5 year warranty on cracks?????
-
- Member
- Posts: 5
- Joined: Mon Jan 17, 2011 8:52 pm
Re: Sinco Customs - Custom fabrication offer!
scott90 wrote:so basically we are looking at 900 for custom made steam tube manifold and 5 year warranty on cracks?????
4 cyl. are $675+gst 6 cyl. $980+gst they come with a minimum 5 year no crack warranty if we fit them and setup the other components it will be 10 no crack warranty.
mike
Re: Sinco Customs - Custom fabrication offer!
Hey,
I am looking at having a manifold made in stainless for a T04z on a 2JZ.
If i was to supply materials (flanges, bends and straight), how much would it be for labour?
Cheers.
I am looking at having a manifold made in stainless for a T04z on a 2JZ.
If i was to supply materials (flanges, bends and straight), how much would it be for labour?
Cheers.